T12 паяльная станция. Настройки
P00: Восстановление параметров по умолчанию, можно выбрать 0 или 1, значение по умолчанию 0, для восстановления 1.
P01: Настройка коэффициента усиления операционного усилителя, значения от 200 до 350 шаг 1, по умолчанию 232.
P02: Напряжение сдвига операционного усилителя, значение от 0 до 250mV, шаг 2, значение по умолчанию 100.
P03: Настройка термопары ℃/mV, значения от 30 до 50, шаг 1, значение по умолчанию 43.
P04: Шаг установки температуры значения, 0,5,10 градусов на 1 щелчок энкодера, 0 блокирует изменение температуры.
P05: Время бездействия до перехода в сон. Значения от 0 до 60 минут, шаг 1. 0 отключает режим сна. При переходе в сон температура паяльника сбрасывается до 200 градусов.
P06: Время сна до отключения, значения от 0 до 180 минут. В диапазоне 0 до 30 шаг 1, после 30 шаг 10. Значение 0 запрещает станции выключается.
P07: Диапазон значений от 0 до 20 с шагом 1. В одних описаниях пишут, что тут устанавливается температура холодного спая, в других что это просто корректировка температуры, в любом случае особого влияния на температуру паяльника я не заметил, так что не совсем понятно для чего это.
P08: Режим выхода из сна. Значения 0 или 1. 0 — для пробуждения нужно повернуть ручку энкодера. 1 — автоматическое пробуждение при движении паяльника или при вручную при вращении энкодера.
P09: Turbo нагрев. Установка уровня турбо нагрева, значение от 20 до 100 градусов, шаг 10.
P10: Время на которое включается Турбо режим. Значения от 10 до 250 секунд, шаг регулировки 5 сек.
P11: Время до сохранения параметров и выхода из меню. диапазон от 4 секунд до 60 секунд
P12: Настройка работы бипера. Значения 0 или 1. 0 бипер выключен, 1 включен.
информация со странички паяльной станции:
P00: restore the default parameters (0 or 1, the default value of 0,0 for not recovering, 1 for the recovery)
P01: Operational amplifier gain (200 to 350 times, step 1, default 230)
P02: Operational amplifier offset voltage (0 ~ 250mV, step 2, the default value of 100, refers to the tip to keep the room temperature operational amplifier inherent output voltage, according to my measurement this voltage varies greatly with temperature, different magnification Not the same, the higher the magnification, if you do not measure, please keep the default value)
P03: thermocouple ℃ / mV data (30 ~ 50, step 1, the default value of 41, refers to the thermocouple need to temperature how much voltage was increased by 1mV, according to the type of thermocouple self-calculation, if you do not understand, please keep Defaults)
P04: temperature adjustment step (0,1,2,5,10 degrees optional, 0 can lock the soldering iron temperature)
P05: sleep time (how long donrsquot not move into sleep) (0 ~ 60 minutes, step 1, 0 is to forbidden the sleep function)
P06: Shutdown time (0 ~ 180 minutes, 0 ~ 30 step 1,30 ~ 180 step 10, 0 is forbidden shutdown function)
P07: temperature correction (+20 degrees, step 1) (due to NTC resistance in the chassis, the soldering station heat will lead to the detection of NTC temperature higher than room temperature, resulting in high temperature compensation of the thermocouple, soldering iron temperature is not accurate,or other causes the temperature is not accurate.If you set the other parameters are correct value but the temperature is still high or low, you can use this parameter correction.For example, to detect the displayed soldering iron temperature is 20 degrees higher than the actual value of this parameter Set to 20)
P08: wake mode (0,1, 0 in the shutdown mode can be rotated the encoder and also can shake the handle to wake up, 1 can only rotate the encoder wake up (Note: press the encoder can not wake up, can only rotate) )
P09: temperature increase mode to increase the temperature to adjustable (20 degrees to 100 degrees adjustable, adjust the pace of 10 degrees)
P10: temperature to increase the duration to adjustable (adjustment range of 10 seconds to 250 seconds, adjust the step 5 seconds)
P11: Parameter setting mode Auto save parameter and return to heating mode Function to active time adjustable (range 4 seconds to 60 seconds)

Measuring Machine normal, lights and display status:
1. Unplugged T12 tip, turn the light flashed off, show SER, 1 seconds after the display 500.
2. T12 plug tip, boot light uniform flashing, indicating rapid heating from room temperature generally show the set temperature to rise, approaching the set temperature, strobe lights. Indicator is not flashing or intermittent flashes, indicating that the tip temperature reaches the set temperature or alternating temperature compensation.
When measuring machines on display digital bounce questions:
Because with the new T12 tip, the tip inside the heater did not burnt, it will be just a little jump start with warm, generally do not need special treatment, the natural use of 1-2 days basically not bounce up. If you need effective immediately, the general recommendations of the temperature to 350 ?-380 ?while heating to the point of tin iron head, burning off after 4-5 minutes, until the tip to cool before you can reboot! (1 no action can be repeated 2-3 times)
Товар тут